[image]

All router interfaces are configured with an IP address and are operational. If no routing protocols or static routes are configured, what information will be included in the show ip route command output for router A?

•  All of the 192.168.x.0 networks will be in the routing table.

•  Routes to networks 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24 will be in the routing table.

•  The routing table will be empty because routes and dynamic routes have not been configured.

•  A default route is automatically installed in the routing table to allow connectivity between the networks.

When a router boots, what is the default order to locate the Cisco IOS if there is no boot system command?

•  ROM, TFTP server, flash

•  flash, TFTP server, ROM

•  flash, NVRAM, TFTP server

•  NVRAM, TFTP server, flash

Which router component is used to store the routing table?

•  Flash

•  NVRAM

•  ROM

•  SDRAM

Which three statements describe the operation of routing with EIGRP? (Choose three.)

•  As new neighbors are discovered, entries are placed in a neighbor table.

•  If the feasible successor has a higher advertised cost than the current successor route, then it becomes the primary route.

•  If hello packets are not received within the hold time, DUAL must recalculate the topology.

•  The reported distance is the distance to a destination as advertised by a neighbor.

•  EIGRP maintains full knowledge of the network topology in the topology table and exchanges full routing information with neighboring routers in every update.

•  EIGRP builds one routing table that contains routes for all configured routed protocols.

• As new neighbors are discovered, entries are placed in a neighbor table.
• If hello packets are not received within the hold time, DUAL must recalculate the topology.
• The reported distance is the distance to a destination as advertised by a neighbor.

11. What two routing protocols use a hierarchal network topology? (Choose two.)

•  IS-IS

•  EIGRP

•  OSPF

•  RIPv1

•  RIPv2

• IS-IS
• OSPF

What command would the network administrator apply to a router that is running OSPF to advertise the entire range of addresses included in 172.16.0.0/19 in area 0?

•  R1(config-router)# network 172.16.0.0 0.0.0.255 area 0

•  R1(config-router)# network 172.16.0.0 0.0.3.255 area 0

•  R1(config-router)# network 172.16.0.0 0.0.15.255 area 0

•  R1(config-router)# network 172.16.0.0 0.0.31.255 area 0

[image]

All routers are running RIPv1. The two networks 10.1.1.0/29 and 10.1.1.16/29 are unable to access each other. What can be the cause of this problem?

•  Because RIPv1 is a classless protocol, it does not support this access.

•  RIPv1 does not support discontiguous networks.

•  RIPv1 does not support load balancing.

•  RIPv1 does not support automatic summarization.

[image]

A network administrator has enabled RIP on routers B and C in the network diagram. Which of the following commands will prevent RIP updates from being sent to Router A?

•  A(config)# router rip
A(config-router)# passive-interface S0/0

•  B(config)# router rip
B(config-router)# network 192.168.25.48
B(config-router)# network 192.168.25.64

•  A(config)# router rip
A(config-router)# no network 192.168.25.32

•  B(config)# router rip
B(config-router)# passive-interface S0/0

•  A(config)# no router rip

Definition