Term
| What is the purpose of the NOMMP 8000.16 (series)? |
|
Definition
| To establish standardized weapons maintenance activities |
|
|
Term
| What does NOMMP stand for? |
|
Definition
| Naval Ordnance Maintenance Management Program |
|
|
Term
| For what 3 families of weapons does the NOMMP provide a ready reference? |
|
Definition
- Air-launched guided missiles and glide bombs
- Aircraft bombs and components
- CADs and rocket motors
|
|
|
Term
| What are the 5 functions of the NOMMP? |
|
Definition
- Guide to daily operation
- Establishes maintenance requirements and responsibilities for all non-nuclear weapons, weapon components, and weapon support equipment
- Provides a basis for training documents
- Functions as a standard reference document
- Provides a ready reference for certain families of weapons
|
|
|
Term
|
Definition
|
|
Term
|
Definition
| Propellant Acuated Device |
|
|
Term
| What basic definition applies to CADs and PADs? |
|
Definition
| Explosive devices used in Aviation Life Support Systems (ALSS) and weapons delivery systems |
|
|
Term
| Because of what two characteristics are CADs utilized for many applications? |
|
Definition
- High reliability
- Ease of maintenance
|
|
|
Term
| What are used to operate bomb rack ejection systems, missile launchers, various dispensers, and to perform several functions in aircrew escape systems? |
|
Definition
|
|
Term
| What are designed to explosively remove the ejection seat and aircrews from an aircraft, stabilize the trajectory of the man and seat combination, separate the aircrewman from the ejection seat, and assist in the opening of the parachute? |
|
Definition
|
|
Term
| What will be done if a CAD or PAD does not freely and fully enter the chamber for which it was specifically designed? |
|
Definition
| It shall be carefully extracted and no other attempt shall be made to install it |
|
|
Term
| In what equipment shall a PAD or CAD never be installed? |
|
Definition
| Any equipment for which it has not been authorized |
|
|
Term
| Some CADs and PADs have the _____ dimensions and are _____ _______. |
|
Definition
Some CADs and PADs have the same dimensions and are physically interchangable.
|
|
|
Term
| What class of ammunition are CADs? |
|
Definition
|
|
Term
| What class of ammunition are PADs? |
|
Definition
|
|
Term
| What does AEPS stand for? |
|
Definition
| Aircrew Escape Propulsion Systems |
|
|
Term
| What are AEPS devices used for propulsion of ejection seats and other equipment during ejection from military aircraft? |
|
Definition
|
|
Term
| What are used to actuate aircraft personnel escape systems, fire extinguishers, cable cutters, line and hose guillotines, and other items in naval aircraft systems and associated equipment? |
|
Definition
|
|
Term
| How shall all CADs and PADs be handled? |
|
Definition
|
|
Term
|
Definition
|
|
Term
| How shall a CAD or PAD suspected of having been fired or subjected to fire be marked? |
|
Definition
|
|
Term
| A disposition on a CAD or PAD suspected of having been fired shall be requested in accordance with what 3 manuals? |
|
Definition
- SPCCINST 8010.12
- COMNAVAIRFORINST 4790.2 (series)
- OPNAVINST 8000.16 (series)
|
|
|
Term
| All suspended ammunition shall be handled in accordance with safety precautions applicable to what? |
|
Definition
|
|
Term
| A device may be considered inert once cerified by whom? |
|
Definition
| An Explosive Ordnance Disposal Inspector |
|
|
Term
| What is an operating or maintenance procedure, practice, etc., which, if not strictly observed, could result in injury or death of personnel? |
|
Definition
|
|
Term
| What is an operating of maintenance procedure, practie, etc., which, if not strictly observed, could result in damage or destruction of equipment or loss of mission effectiveness? |
|
Definition
|
|
Term
| What is an operating or maintenance procedure, condition, etc., which is essential to emphasize or clarify? |
|
Definition
|
|
Term
| What is the rule for how CADs and PADs installed in aircraft must function? |
|
Definition
| They must function perfectly the first time |
|
|
Term
| What will be the result if devices fail to fire when needed? |
|
Definition
| Severe injury or death of the aircrew and damage to the equipment |
|
|
Term
| Upon what does the performance of CADs and PADs depend? |
|
Definition
| Careful handling, installation, and storage |
|
|
Term
| Will repair be performed on CADs and PADs? |
|
Definition
|
|
Term
| What will happen if a CAD or PAD is damaged or contaminated? |
|
Definition
| The item will be replaced |
|
|
Term
| How should CADs and PADs not be handled? |
|
Definition
|
|
Term
| It is considered a reportable defect if a device, or its storage container, shows what? |
|
Definition
| Evidence of rough handling, being dropped or damaged, or any other visible defect |
|
|
Term
| Which way should rocket motors not be laid on any surface? |
|
Definition
|
|
Term
| Which CADs and PADs shall not be opened or removed from sealed containers for inspection? |
|
Definition
| Environmentally sealed CADs |
|
|
Term
| CADs and PADs found to have no _____ _____ shall not be installed? |
|
Definition
CADs and PADs found to have no Identification Markings shall not be installed
|
|
|
Term
| What is the only on-equipment work authorized? |
|
Definition
| Removal, inspections, and installation |
|
|
Term
| In what cases is on-equipment work other than removal, inspection and installation authorized? |
|
Definition
| When detailed in the aircraft/equipment technical manual, or an authorized approved technical directive |
|
|
Term
| In what case is cannibalization of CADs and PADs by O-level maintenance authorized? |
|
Definition
| With the approval of the Cognizant Wing (ashore) or Carrier Air Wing (afloat) in accordance with COMNAVAIRFORINST 4790.2 (series) and OPNAVINST 8000.16 (series) |
|
|
Term
| To whom is damaged or broken lockwire on rocket motors to be reported? |
|
Definition
| The Cognizant Field Activity, IHDIV NAVSURFWARCEN Indian Head Maryland |
|
|
Term
| Replacement of what is not authorized on rocket motors? |
|
Definition
|
|
Term
| What purpose do safety pins and devices serve? |
|
Definition
| Prevent inadvertent firing of CADs and PADs |
|
|
Term
| What purpose do protective caps and plugs serve? |
|
Definition
| Prevent contamination of devices by moisture and foreign matter |
|
|
Term
| In what case will removed CADs and PADs not be stored in a Ready Service Magazine? |
|
Definition
| When they are required to be reinstalled the same day |
|
|
Term
| What does HERO stand for? |
|
Definition
| Hazards to Electromagnetic Radiation to Ordnance |
|
|
Term
| What is the purpose of the QUAL/CERT program? |
|
Definition
| So that sailors, marines and civilians required to handle explosive actuated devices are qualified to perform all functions safely |
|
|
Term
| What are the five levels of certification? |
|
Definition
- TM - Team Member
- I - Individual
- TL - Team Leader
- QA - Quality Assurance
- SO - Safety Observer
|
|
|
Term
| During all ordnance handling evolutions, a ____ member team is required. |
|
Definition
|
|
Term
| What three positions must be filled in an ordnance handling team? |
|
Definition
| Safety Observer, the person performing the procedure, and the Tool/Cartridge handler |
|
|
Term
| What are lot numbers used to distinguish? |
|
Definition
| Date of manufacture and group in which they were produced |
|
|
Term
| Where is the information to decipher a lot number found? |
|
Definition
|
|
Term
| Of how many parts does a lot number consist? |
|
Definition
|
|
Term
| What letter is not used in the month to alpa conversion? |
|
Definition
|
|
Term
| Where are lot numbers located? |
|
Definition
| On the manufacturer identification plate or imprinted on the CADs and PADs |
|
|
Term
| What is defined as: the specific period of time during which a Cad or PAD is allowed to be used? |
|
Definition
|
|
Term
| What is defined as: the period of time beginning from the date of manufacture that CADs and PADs can remain in their hermetically sealed containers and still be serviceable? |
|
Definition
|
|
Term
| What is defined as: the period of time a CAD is allowed to be used after the hermetically sealed container is opened? |
|
Definition
|
|
Term
| On what form in logbooks will CAD and PAD entries be made? |
|
Definition
|
|
