If Philippine Mahogany costs $3.10 per board foot, how much would an 8 foot 2x6 cost?

96"x2"x6"=8 board feet

8 bd ft X $3.10= $24.80

If 3/4" cherry plywood costs $3000 per thousand (square feet), what would the price be for two sheets of plywood?

$3000/1000 sq ft =         /64 sq ft

$3000/1000 sq ft =       $192/64 sq ft

S4S Means that the wood is smooth on all four faces and parallel and square. It usually costs more for this.

What is the difference between rough lumber and S2S straight lined lumber?

Rough lumber hasn't been jointed or plained on the faces or edges of the boards, so it is cheaper, but requires more labor to get the material ready to build with.

If a cabinet shop charges $60 per hour with a minimum charge of $30, what would a customer pay for a 45 minute job?

To build a rectangular frame with mitered corners, what angle of cut is required on the ends of your piece of wood?

To build a six sided frame with mitered corners, what angle of cut is required on the ends of your six pieces of wood?

What is the major difference between domestic and import plywood?

How many 11.5"x 15" pieces can you get from a standard sheet of plywood?

How many board feet in a piece of lumber 8/4x8"x60"?

2"x8"x60"

=6.66 bd ft

223/12=

18.58 = 18 feet and something

18x12=216 inches

223"-216"=7 inches

Therefore the answer is 18 ' 7"

True or False, a miter joint is strong enough that it doesn't need to be reinforced

As in a picture frame

False, a miter joint needs reinforcement unless it is going on a cabinet. Then the cabinet will help to hold the joint together.

How many sheets of plywood do you need to purchase the make 16 pieces 23 1/2"x 30" cabinet sides?

You can get 2 rows and 3 columns per sheet.

So 2x3=6 pieces per sheet

You need 16 pieces so 6x3 sheets=18 pieces

so you need to buy 3 sheets of plywood

How many sheets of plywood would you need to purchase to make six cabinet sides that measure exactly 24 inches wide by 76 inches long?

You can only get one piece per piece of plwood (remember the saw kerf!!!) so

you would need to buy six sheets of plywood.

It is a tool used to find the profile of millwork so that it can be duplicated with a shaper or router.

Finished height is 36"

Cabinets are 34 1/2" tall and a 1 1/2" thick counter top brings the final height to 36"

12mm roughly equals 1/2" 

so 25.4mm= 1 inch

What is the difference between a rabbet and a dado?

A dado is a groove cut across the grain on the interior of the board. A rabbet is a groove cut along the outside edge of a board. It can be either with or across the grain.

http://eberhardt.bz/GME_Wood_Land/GME_Woodworking_Stuff/4_Information/1_Dado_Blades.pdf

If a sander uses PSA sandpaper, what does psa stand for?

When using a jointer to straighten a bowed board, is it best to joint the concave side or the convex side?

It is best to straigten the concave side.

Joint one face then

plane opposite face

joint one edge and

rip (on table saw) the opposite edge

Using dowels, old cut up tape measure, or wood strips. Lay them on the dried contact cement about 6" apart. Then position the plam. When it is where you want it, begin sliding the pieces out while j- rolling the plam.

On a cultist that lists a piece of wood, 23 1/2"x19", which way is the grain running?

How do you repair a minor dent on a part prior to finishing?

Using a wet rag and a hot iron, put the rag on the dent and use the iron to create steam and pull the dent out.

The first is a stack dado, It has blades of different thicknesses. You simply stack the blades together until you get the width needed.

The other type is a V-blade dado. It is two blades that have a cam that can be adjusted to make the blade wider or narrower.

http://eberhardt.bz/GME_Wood_Land/GME_Woodworking_Stuff/4_Information/1_Dado_Blades.pdf

A piece of 3/4" material at the top back part of a cabinet that you would screw through to attach the cabinet to the wall.

It tends to shrink, when that happens sometimes it can warp, bow or crack

False, wood is always moving. Finish just slows down the movement.

How many pieces of plywood can you get out of a sheet of plywood if the pieces are 15 1/2" wide and 23 1/2" long?

3 rows and four columns equal

3x4= 12 pieces per sheet

The outfeed table on the Jointer should be set to;

a) highest point of the rotation of the knives

b) lowest point of rotation of the knives

c) middle point of rotation of knives

d) even with the center of the axis

1. You save labor in not having to mill your wood

2. Being able to see your wood without mill marks on it

3. Less waste of wood

4. Less wear and tear on your machines

Name two machines need to make a piece of wood flat, parallel and uniform thickness.

What unit of volume do we use in the the shop?

A number 8 screw is smaller than a number 10 screw.

You want to bullnose (1/2) round a piece of material that is 3/4" thick, draw a side view of this then

You only own 1/4 round bits, what size bit do you need and how do you measure this- draw it.